QMT Features: December 2014
Wires and cables: the measurement of success
All wires and cables that distribute power need their resistance measuring

It is necessary to measure the resistance of all wires and cables that are used to distribute power including the cable used to wire domestic property says Nathan Barwell business development engineer, Seaward Group.

The resistance property of cable needs to be low enough to ensure that it will not heat up too much when the maximum rated current is passed through it. The higher the resistance, the hotter the cable will become with a set current flowing through it. Therefore, the manufacturer must ensure that the resistance per metre of the cable produced complies with the published specification and any international standards that may apply.
It is however important that the maximum permitted resistance per metre is achieved. From the cable manufacturer’s point of view, the lower the resistance value per metre the larger the diameter of the cable and so the greater amount of copper that’s used. Copper is expensive and is the main contributor to the cable costs - the lower the amount of copper used the greater the manufacturing cost and raw
material savings.

The accurate and reliable measurement of resistance is therefore important to enable the cable manufacturer to achieve the minimum cable diameter while remaining within the declared specification. This is a very powerful argument for good resistance measurements in the cable industry and the accepted method of measuring metre lengths is to use a one metre cable clamp.

Measurement methodology

To ensure meaningful measurement it is necessary to define the conditions: the length of cable to be measured, the temperature at which the cable is to be measured and the current used to measure the resistance are all factors that can influence testing and results – so these need to be clearly defined.
When it comes to cable length, it is normal practice to measure a metre length of cable and special cable clamps are available for holding the wire. The clamp should include connections for the current and connections for the potential points. The use of a current clamp eliminates inconsistent readings due to small changes in the length of cable measured. Care should be taken not to stretch the wire when placing it into the clamp, as this will increase its resistance.

The clamp should also have provision for shielding the wire against draughts, which can cause temperature variations. An additional desirable feature of the clamp is the provision for mounting a temperature sensor adjacent to the cable to be measured. The diagram below shows the connections to the wire being measured, note that the current connections are placed outside the potential and the exact one metre length is measured between the potential connections.

Most modern digital microhmmeters like those available from Cropico (part of the Seaward Group) all use the ‘four terminal’ principle of measurement, sometimes referred to as the ‘Kelvin’ or ‘Thompson’ principle. It is recommended to employ this measurement technique for determining values below 100 ohms as lead resistance is eliminated from the measurement.

When measuring, a current is passed through the cable to be measured and the volt drop between the potential connections is measured. The potential leads carry a negligible current, and according to Ohm’s law (Resistance = Volts/current) if no current is flowing then the resistance of the potential connection wire is zero. (The resistance of the potential leads is therefore not included in the wire measurement). It is important to position the connections correctly to ensure the correct value is measured – they should be placed a few centimetres outside the potential connections, and the potential points located exactly at the points to be measured.

Temperature influence
All wires and cables have a temperature coefficient; their resistance value will vary according to the temperature. Some materials have a relatively high temperature coefficient (e.g. copper = 3250ppm/°C) and the measured resistance value will depend upon the temperature. This temperature is influenced either by ambient temperature changes or the heating effect of passing the measurement current through the cable.

The effects of ambient temperature changes can be compensated for when using a microhmmeter like the Cropico DO5000. This temperature compensation operates by measuring the ambient temperature with a Pt100 temperature sensor and then correcting the measurement by the sample’s temperature coefficient and referencing the measurement to 20°C – by using this facility all measurements are relative to the same temperature.

Compensating for the heating effects caused by the measuring current is not quite so easy. The temperature compensation method used for ambient temperature changes can be used but to be effective the cable should be submerged in a tank of liquid (water is normally used) and the temperature sensor used to monitor the liquid.

The liquid bath will dissipate and stabilise the temperature from the cable, however this solution can be costly and messy. An improved solution is to limit the measurement current and the time the current flows through the cable thereby reduce heating effect. The DO5000 has the ability to both vary the measurement current and reduce the measurement time to a single shot measurement of approx. 0.5 seconds or in fast mode 0.02 seconds. The table shows the resistance of wire and cables according to temperature.

It is also important to note the possible causes of measurement errors. Inconsistent measurement conditions, incorrect cable clamp, positioning of potential measurement connections vary, ambient temperature variations not compensated for, measurement varying due to changes in temperature, draughts blowing across cable sample causing small changes in cable temperature, cable being heated by measuring current causing a continual drift in measurement and poorly made connections and oxides or dirt on cable producing high resistance at connection points can all play a part in skewing measurement the accuracy of results and must be taken into account when considering an effective  so measurement solution for wire and cable applications.

Using a microhmmeter such as the DO5000 combined with a cable clamps can help to improve measurement accuracy and consistency. In a typical cable manufacturing environments, it is linked to a specialist clamp which holds a standard one metre length of cable or wire in place as the copper strands passes along the bobbin extruder. The clamp incorporates separate current and potential measurement connections, which are attached to the cable for resistance measurements to be made.

There are three cable models in the Cropico range and these offer the ability to accurately clamp and measure cable up to 1000mm2.  There is also a model that has an integrated water bath which will automatically bring the cable under test to a specific temperature. Programmable current levels and the selection of different test speed settings give the Cropico tester the flexibility to accurately measure the resistance values of different cable products. These include single end and plain soft wires through to bunched, stranded and large diameter rope type conductors.

Accurate and reliable in-line cable resistance measurements taken in this way enable cable manufacturers to maintain optimum operating efficiencies in terms of copper raw material use. The versatile Cropico D05000 has programmable current settings in 100 steps from 10µA to 10A and measures from 3mO to 30kO with a resolution of 0.1µO and ±0.03% accuracy.

Variable measurement speed settings of 50, 25 or 2.5 per second allows the selection of high speed testing for production line applications, a medium mode where the device under test needs more time to settle or a slow speed for manual operation where display clarity is a priority.

True four-wire resistance measurement eliminates lead resistance errors, while auto averaging and automatic temperature compensation with 20°C referencing or other user-defined settings increases true measurement accuracy. All these options are included in the basic D05000 unit as well as a data logging function which stores up to 4000 readings with date and time stamp. Statistical analysis of these values allows the display of max/min/average values as well as peak to peak and standard deviation.
Interfaces can be added for remote control and integration into automated test systems.  For applications where portability is required the Cropico 5001 model can be powered from either a mains supply or by rechargeable batteries. The charger is also incorporated into the unit and the full 10 Amps pulsed measuring current is available when used in battery mode.
You can now view all QMT Magazine issues on your favourite tablet or smart phone.
Download the free Quality Manufacturing Today App from the Apple iTunes App Store or from QMT Magazine on Google Play.

Rob Tremain Photographer
Click above to see full page display and links to QMT articles.
MACH 2016 logo
Bowers logo
Vision 2016 ad
Nikon logo
TCT Inspex 2016 logo
Prodim logoi
Creaform logo